bcdxt manual pdf probably later version is at pub/Uni age_pdf BCDXT < UnidenMan4 < TWiki. This guide is a full featured, 26 page spiral-bound instructional Mini-manual, covering all aspects of this very capable scanner. Mini-manual size is x8 inches. DImage_/Manual/ (1 of .. This page applies to the following scanner(s): BCDXT BCT15X BCDXT BCXT.
|Published (Last):||26 January 2009|
|PDF File Size:||6.92 Mb|
|ePub File Size:||4.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
The large arrow shows the direction to the selected POI.
Any transmission received on the frequency will not be heard but you will still see uniden bcd996xt manual signal strength bars. Trunking Display Mode 2. There is no ‘per channel’ delay; you must set the delay for the whole system all sites, all groups, all channels.
To the Close Call Hits system: The uniden bcd996xt manual base frequency can also be found using the Band Plan Calculator at the online Wiki. Dimmer Circuit – a special wire lets you connect to the dimmer circuit of your vehicle so the vehicle’s dimmer also dims the scanner’s lighting.
Press then to mannual group quick keys on or off in Scan Mode. Infinite uniden bcd996xt manual you must press Hold after a page to resume standby mode.
UNIDEN BCDXT USER MANUAL Pdf Download.
Repeat for uniden bcd996xt manual block as needed and you will return to the ‘ Edit Sys Option ‘ menu. Leave the speed limit blank to be alerted regardless of your speed. You can use the band scope in normal mode the bars are all updated with the most recent signal strength or ‘Max Hold Mode’ the bars update only if there is a stronger signal than one previously stored for the current position.
The frequencies also have to be in LCN Logical Channel Number order or the uniden bcd996xt manual ‘slot’ for the system to trunktrack properly.
To toggle Msnual bands off or on press uniden bcd996xt manual number key for each band. Press to enter the Menu mode for a displayed channel in Scan Mode.
Uniden BCD996XT User Manual
Public safety radio systems on the same frequency are usually set up at a distance of 40 miles apart, or more. Press and hold 7 Att for global attenuation. If you can’t hear a control channel when you step through the trunking frequencies in manual modeyou either don’t have all the frequencies or uniden bcd996xt manual too far away to receive the control channel and the system.
If you turn off all groups in a system you will not be able to turn any back on and also uniden bcd996xt manual ‘ Nothing to Scan ‘. For more information about Band Scope Mode: Tone-Out Standby Mode uniden bcd996xt manual used if you know and use programmed tones.
Uniden BCD996XT Owner’s Manual
So when you are trunktracking a system, you are uniden bcd996xt manual to active IDs transmitting in the system each uniden bcd996xt manual the first available frequency in the system.
To hold on a CC hit press Hold. The scanner’s menu lets you select options that let you set up and use the scanner using the MENU key. Press to enter a hyphen when entering an ID while programming. You can also do this by pressing and holding SQ in scan mode.
Uniden bcd996xt manual sure that the cable terminates in a female, 9-pin serial connector and you select the correct baud rate bps for the rear serial port. See also Set ID Format.
Right away you may want to check these settings in the ‘ Settings ‘ menu. The default setting is 2 seconds.
Set Delay Time sets the delay in seconds the amount of time the scanner stays on a channel after the uniden bcd996xt manual has ended before moving to the next channel. Public Service, 33 cm Ham.
Press and hold to unlock and enable all groups and channels in a system in Scan Hold Mode. Go to the Program System menu and choose New System. To Select a Uniden bcd996xt manual turn the scroll control.