ASTM A Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility.
|Published (Last):||3 August 2016|
|PDF File Size:||3.26 Mb|
|ePub File Size:||5.35 Mb|
|Price:||Free* [*Free Regsitration Required]|
General Requirements for Stainless Steel Bars, Billets, and Forgings This provides dimensional tolerance, straightness, and finish descriptions for hot or cold finished bar, squares, angles, channels, tees and other shapes. Tensile Strength ksi min.
Alloy-steel and stainless steel bolting materials for high temperature or high pressure service and other special purpose applications. They shall be formed in different shapes such as sheets, strips, plates and flat bars.
A Austenitic stainless steel susceptibility to intergranular attack under structural analysis. Proceed aastm Checkout Continue Shopping. Find out what NKS can do for you.
A General requirements for flat-rolled stainless and heat-resisting steel plate, sheet, and strip describes surface finishes for sheet, strip, plate; defines edge conditions; provides dimensional and flatness tolerances; describes shipping requirements; and requirements for heat treatment, test specimens, test methods.
If the document is revised or amended, you will be astmm by email. Standard specification for steel wire for masonry joint reinforcement This includes stainless steel wire for this application.
These treatments do not remove heat tint from welding. Documents supporting compliance can be found at www. The steels shall adhere to specified q666 composition requirements. It also resists corrosion in marine atmospheres and has excellent resistance to intergranular corrosion in the as-welded condition.
This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions. Types and L provides corrosion resistance in a wide range of moderately aetm and reducing conditions, fresh water and non-marine applications. Add to Alert PDF.
and L Stainless Steel – NKS
You may delete a document from your Alert Profile at any time. E Specification for permanent metal railing systems and rails for buildings. All values are maximum values unless otherwise specified. This standard is not included in any packages. The values given in parentheses are for information only. C Standard guide for design, selection, sstm installation of exterior dimension stone anchors and anchoring systems This says that metal in contact with stone should be a series stainless, but other materials can be used if properly protected atm moisture and galvanic corrosion.
Test method for anchorage of permanent metal railing systems and rails for buildings. ASTM A may also need to be specified.
Standard guide for design, selection, and installation of exterior dimension stone anchors and anchoring systems This says that metal in contact with stone should be a series stainless, 6a66 other materials can be used if properly protected against moisture and galvanic corrosion. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined.
E Test method for structural performance of sheet metal roof and siding systems by uniform static air pressure difference. Actual data on any particular product or material may vary from those shown herein.
Stainless Steel Type 316/316L
Condition Yield Strength ksi min. If filler metal is required, Type is normally used.
Please first verify your email before subscribing to alerts. Carbon and alloy steel nuts for bolts for high pressure or high temperature service or both includes stainless steel. Standard specification for welded stainless steel austenitic – series including and zstm ferritic series mechanical tubing round, square, and rectangular tubing for structural applications Note: Copper and stainless steel wire are used for wire ties.
304 and 304L Stainless Steel
Type L should be specified for welded applications as the low carbon version q666 chromium carbide precipitation and enhances the corrosion resistance in the as-welded condition. Test method for pullout resistance of astn and anchors embedded in masonry mortar joints.
Need more than one copy? E Test method for anchorage of permanent metal railing systems and rails for buildings. A Chromium-Nickel Stainless Steel Weaving and Knitting Wire composition and mechanical requirements of common types of stainless steel wire intended for weaving and knitting.
ASTM-A Alloys | E. Jordan Brookes Company
F Specification for food service equipment hoods for cooking appliances. A Standard specification for rolled floor platestainless steel. We have no amendments or corrections for this standard. The finish descriptions are very general.